Effect Of Heat Treatment Research Articles

Heat treatment Effect of Mg-5Sn-3Zn-1Mn Alloy with different Silicon addition

Heat treatment Effect of Mg-5Sn-3Zn-1Mn Alloy with different Silicon addition

Effect of Heat Treatment on the Material Property and Cell Viability of Wire Arc Additively Manufactured Ti6Al4 V

Effect of Heat Treatment on the Material Property and Cell Viability of Wire Arc Additively Manufactured Ti6Al4 V

Investigation of Two Laser Heat Treatment Strategies for Local Softening of a Sheet in Age-Hardening Aluminum Alloy by Means of Physical Simulation

AbstractCar manufacturers increasingly aid high-strength aluminum alloys for their advantageous weight-to-strength ratio, but their limited formability poses challenges in plastic deformation processes. Tailored heat-treated blanks (THTBs) are a propitious approach to improve formability. Surface laser treatment is the predominant technology for obtaining THTB. To design this process quickly and accurately, without material waste, the use of physical simulation is increasingly promising. It allows replicating the process on a lab-scale and studying posttreatment mechanical and metallurgical properties. By adopting Gleeble® physical simulator, this study investigates the softening effects of local surface laser heat treatment on a EN AW 6082 T6 aluminum alloy blank. Two laser movement strategies—single linear path and multiple rectangular paths—were investigated at two treatment speeds for each. A finite element (FE) model was developed for simulating the process under all explored conditions. FE-derived thermal cycles were reproduced by means of physical simulation. After physical tests, alloy mechanical properties were evaluated. Results show that these properties depend on both the peak temperature thermal cycle and the interaction time between the laser source and the material surface. The comparison between the two strategies revealed that the multiple rectangular paths strategy allows to achieve a wider softened area at comparable interaction times.

Effect of direct aging heat treatment on microstructure and mechanical properties of Laser Powder Bed Fused Maraging steel 300 grade alloy

Abstract This paper investigates the effects of a 6-hour direct aging heat treatment at 490°C on the mechanical, tribological, and microstructure characteristics of laser powder bed fused maraging 300 steels, which is produced at various laser energy densities. After direct aging heat treatment, the grain boundaries become irregular and vague due to the residual stress releasing, squeezing of precipitates into the grain boundaries, and phase transformations. The XRD analysis reveals the reverted austenite (γ') phase forms during age treatment due to the inevitable reversion of metastable martensite to the stable reverted γ' phase. The heat-treated samples microhardness rises with rising the Laser Energy Density (LED) from 61.33 to 92.10 J/mm3 due to a decrease in the reversed austenite phase and a further rise in LED decreases the microhardness due to a rise in the reversed austenite phase. The heat-treated sample produced at LED of 92.10 J/mm3 shows maximum yield, ultimate tensile strengths, and minimum elongation percentage due to its high microhardness, and the fractography results show the failure mode as a mixed brittle and ductile fracture. The wear rate of the heat-treated additively manufactured maraging 300 steel decreases as the LED increases from 61.41 to 92.1 J/mm3 and a further rise in LED increases the wear rate. The wear rate rises with a rise in sliding velocity from 1.5-3.5 m/s. The dominant wear mechanism was observed as abrasion with small grooves and saplings.

Enhancing tensile properties of MIG welded AA6061 joints: Effect of pulse mode and post-weld heat treatment

Metal-Inert Gas (MIG) welding is one of the most important welding technologies commonly used in the manufacturing industry due to its high degree of automation and welding adaptability. However, softening is prone to occur in fusion zone (FZ) and heat affected zone (HAZ) of AA6061 MIG welded joint, which limits its application. In this work, AA6061 was welded by MIG welding with different pulse modes, and the post-welding heat treatment was carried out. The results show that the dual pulse MIG (DP-MIG) and PWHT can significantly improve the mechanical properties of AA6061 butt joint, and its ultimate tensile strength (UTS) is 331.3 MPa, even more than 90% of the base material (BM). In this paper, the microstructure of welded joints under different pulse conditions before and after PWHT was compared, and the relationship between the welding process, microstructure, and mechanical properties was established Furthermore, the influence mechanisms of pulse mode and PWHT on the mechanical properties of welded joints were explained in detail.

Effect of Post-Deformation Heat Treatment on the Microstructure and Properties of Inconel 617 Alloy

Effect of Post-Deformation Heat Treatment on the Microstructure and Properties of Inconel 617 Alloy

Factors affecting the formation of delayed bitterness in sweet orange (Citrus sinensis (L.) Osbeck) juice

Formation of delayed bitterness is an intractable problem in the processing of citrus juice. This study analyzed the distribution of main bitter-causing substances in sweet orange and the effect of heat treatment, storage temperature, clarification, and homogenization on the limonin content in sweet orange juice. The segment membrane accounted for 34–42% of limonin in the fruit and 21–45% of limonoate A-ring lactone (LARL). Heat treatment accelerated the formation of limonin in juice. Pectinase treatment appeared to facilitate the formation of limonin by reducing the pH of juice. In addition, refrigeration at 4 °C was found to restrain the formation of limonin in juice by inhibiting the activity of limonin D-ring lactone hydrolase (LDLH). In conclusion, segment membrane may have a great contribution to the delayed bitterness of sweet orange juice due to its abundant LARL. These results may provide some guidance for citrus processing and bitterness removal.

Heat treatment effects on tribocorrosion resistance of Inconel 718® alloy produced by conventional and laser powder bed fusion methods

Heat treatment effects on tribocorrosion resistance of Inconel 718® alloy produced by conventional and laser powder bed fusion methods

High Velocity Oxy-Fuel Thermally Sprayed rGO Reinforced Alumina-Based Coatings on 17-4 PH Steel: Exploring the Effect of Flame Heat Treatment

High Velocity Oxy-Fuel Thermally Sprayed rGO Reinforced Alumina-Based Coatings on 17-4 PH Steel: Exploring the Effect of Flame Heat Treatment

Erratum to “Effect of short heat treatment on mechanical properties and shape memory properties of Cu–Al–Ni shape memory alloy”

Erratum to “Effect of short heat treatment on mechanical properties and shape memory properties of Cu–Al–Ni shape memory alloy”

Effect of post-weld heat treatment on mechanical and microstructural properties of high strength steel weld metal

The usage of high strength steel (HSS) is steadily increasing, primarily driven by the pursuit of weight reduction, leading to a subsequent decrease in greenhouse gas emissions. This paper investigates the impact of various post-weld heat treatment (PWHT) temperatures of 525 °C, 550 °C and 575 °C with a holding time of 2 h on both the microstructure and mechanical properties of weld metal produced using a HSS metal cored wire. The investigation reveals that PWHT does not significantly alter strength but has a more pronounced influence on toughness. The as-welded condition exhibited the highest toughness. Among the samples subjected to the PWHT, the one treated at 575 °C showed the highest impact energy, reaching 69 J at −60 °C. This outcome is attributed to the increased presence of acicular ferrite in the microstructure, surpassing that of samples subjected to PWHT at different temperatures.

Effect of Heat Treatment on Microstructure and Mechanical Properties of TA15 Titanium Alloy Repaired by Laser Deposition

Effect of Heat Treatment on Microstructure and Mechanical Properties of TA15 Titanium Alloy Repaired by Laser Deposition

Effects of oil heat treatment on poplar wood properties: A pilot scale study

Pilot-scale oil heat treatment was conducted to enhance the quality of poplar wood obtained from a fast-growing plantation. Three target temperatures, namely 180, 190, and 200 ˚C, were chosen for the oil heat treatment process. Clear, small specimens were cut from the lumber, following the prescribed standards for assessing wood quality. Light microscopy revealed the ruptures and deformation of the wood cell wall as the treatment temperature increased. The volumetric swelling of the treated specimen decreased proportionally with the increase in treatment temperature. The impact of oil heat treatment on the mechanical properties of wood varied depending on the specific type of mechanical strength and processing temperature. The modulus of rupture, toughness, and hardness of the treated specimens drastically decreased at 200°C. However, the specimens treated at 200°C exhibited much lower mass loss during the fungal decay test. The results of the analytical test showed an increase in the crystalline cellulose content and thermal stability of the treated wood, due to the thermal degradation of hemicelluloses and amorphous regions of cellulose. Overall, it is concluded that oil heat treatment of poplar wood in the optimal temperature is an efficient approach to upgrade its quality with minimal reduction in mechanical strength.

Residual stress relief strategy in thick steel weldments via local induction heat treatment: Simulation and neutron diffraction experiment

This study investigated the effect of local induction post-weld heat treatment (PWHT) on residual stress relief in thick submerged arc welded steel plates. A combination of numerical and neutron diffraction methods was used to examine the effect of various PWHT parameters, such as annealing temperature and holding time, on the relief of residual stress in welded plates with various thicknesses. A sequentially coupled thermal–mechanical finite element model was used to calculate the residual stress distribution in welded AH36 steel plates before and after PWHT. The model was validated by comparing its predictions with the experimental measurements, and the results showed good agreement. The residual stress of the thick welded plates was effectively reduced via PWHT with local induction. The primary mechanism for this stress release was identified as stress relaxation caused by creep strain. Furthermore, a process map was established considering the PWHT conditions and plate geometry. This map provides a means of determining the optimal PWHT conditions to achieve desired stress reduction levels.

Corrosion resistance of additively manufactured aluminium alloys for marine applications

Additive manufacturing opens new possibilities for designing light-weight structures using aluminium alloys. The microstructure of two Al alloys and their corrosion resistance in NaCl and natural seawater environments were investigated. The newly designed Al-Mn-Cr-Zr based alloy showed a higher corrosion resistance than reference AlSi10Mg alloy in both environments in as printed and heat-treated conditions. The corrosion initiated in the Al matrix along the precipitates in the alloys where the Volta potential difference was found the highest. The coarser microstructure and precipitate composition of the new Al-alloy led to the formation of a resistant passive film which extended the passivity region of the Al-Mn-Cr-Zr alloy compared to the AlSi10Mg alloy. The effect of heat treatment could be seen in the microstructure as more precipitates were found in between the melt pool boundaries, which affected the corrosion initiation and slightly the pitting resistance. Overall, this study shows that a newly designed Al-alloy for additive manufacturing has a suitable corrosion resistance for applications in marine environments.

PSI-18 Effects of heat treatment and multi-carbohydrase supplementation on the digestibility of phosphorus in field peas fed to growing pigs

Abstract Most plant-based feed ingredients contain about two-thirds of their total P as phytate. Mineral elements are chelated to phytate or entrapped in plant cell walls, and microbial or enzymatic breakdown of cell walls may be able to release entrapped P, thus leading to improvement of the apparent total tract digestibility (ATTD) of P in pigs. Heat treatment is one of the processing methods that improve the digestibility of fiber in various feedstuffs for pigs. Therefore, this study aimed to determine the effects of heat treatment and multi-carbohydrase supplementation on the ATTD and standardized total tract digestibility (STTD) of P in peas fed to growing pigs. A total of 18 pigs (23.9 ± 1.3 kg) were assigned to 1 of 3 diets in a completely randomized design to give 6 replicates per diet. Three experimental diets were formulated: 1) non-heated or 2) heat-treated (pelleted) peas as the sole source of P, and 3) heat-treated peas with multi-carbohydrase supplementation. Pigs were individually housed in metabolism crates for 12 d, including 7 d for adaptation and 5 d for total collection of feces. Pigs were offered their daily ration at 2.8 times their maintenance energy requirement. Samples of ingredients, diets, and feces were analyzed for dry matter, Ca, and P. Fecal samples were analyzed for mixed bacterial mass (MBM) and volatile fatty acids (VFA) concentrations. Data were analyzed using the PROC MIXED of SAS. The statistical model included diet as fixed effect and replicate as random effect. An alpha level of 0.05 was used to determine statistical significance and P ≤ 0.10 was considered a trend. Pigs fed the diet that contained heat-treated peas with carbohydrase supplementation tended to have greater (P < 0.10) ATTD and STTD of P than pigs fed the diet containing heat-treated peas without enzyme. The values of STTD of P were 54.4, 47.3, and 55.0% for diets containing raw peas, heat-treated peas, and heat-treated peas with carbohydrase supplementation, respectively. Heat treatment and enzyme supplementation did not affect the ATTD of Ca in peas fed to growing pigs. No significant differences were observed in fecal MBM-P and VFA concentrations. In conclusion, carbohydrase supplementation tended to increase the digestibility of P in heat-treated peas fed to growing pigs, however, there was no difference in P digestibility between raw and heat-treated peas. Heat treatment and carbohydrase supplementation did not affect fecal MBM-P and VFA concentrations in growing pigs.

Effect of heat treatment at mild temperatures on the composition and physico-chemical properties of Scots pine resin

Effect of heat treatment at mild temperatures on the composition and physico-chemical properties of Scots pine resin

Effect of Heat Treatments on the Mechanical Properties of Some Selected Metals (Al, Cu & Zn)

Effect of Heat Treatments on the Mechanical Properties of Some Selected Metals (Al, Cu & Zn)

Effect of heat treatment on improving OER activity of NiFeOOH based aerogels: A combined experimental and theoretical study

Enhanced catalytic activity of oxygen evolution reaction (OER) catalysts is necessary to lower the cost of green hydrogen production. This study focuses on the use of a simple strategy of heat treatment to enhance the catalytic activity of NiFeOOH-based aerogels. The study shows that heat treatment of this aerogel at 150°C leads to significant improvement in its catalytic activity, as evident in the staircase voltammetry results. To understand how heat treatment improves the catalytic activity, a DFT+U calculation was carried out on heat-treated and non-heat-treated catalysts. The calculation shows that the overpotential for OER decreases with heat treatment, which is related to the relative stability of the intermediates in heat-treated and non-heat-treated catalysts. Also, it has been found that heat treatment decreases work function, which might improve charge transfer and, thus, catalytic activity. Our calculations are in line with the experimental results that show the release of crystalline water at 150°C which enhances the catalytic activity, and the formation of dense NiFeOx phase at higher temperatures which results in lower activity.

Effects of heat treatments and cross‐linking on the crystal structure and torsional properties of polyester fibers

AbstractArtificial muscles have attracted great attention as actuators and coiled and twisted monofilament actuators are considered the most promising ones. In the present work, the torsional properties of poly(hexamethylene adipamide) (PA66), poly(ethylene terephthalate) (PET), and high‐strength PET (HTPET) monofilaments were investigated. Furthermore, cross‐linked PET (CPET) monofilaments were melt‐spun by adding 1 wt% of 2‐dimethoxy‐2‐phenylacetophenone (ultraviolet (UV) initiator) and triallyl iso‐cyanurate (cross‐linking agent) in PET chips under UV radiation. The HTPET monofilaments had the highest torsional modulus of 1.1 GPa followed by the PET (0.8 GPa) and PA66 (0.6 GPa) monofilaments. Subsequently, the HTPET monofilaments were subjected to heat treatments under tension. When the heat treatment time was 10 min, the mechanical properties of the HTPET monofilaments also tended to first increase and then decrease with the rise of heat treatment temperature. The molecular arrangement and crystal structure of the HTPET monofilaments were gradually improved with the prolongation of tension heat treatment. The tensile strength and initial modulus of the HTPET monofilaments were 871.4 MPa and 15.8 GPa, respectively. The mechanical properties of the CPET monofilaments first increased and then decreased with the increase of the drawing ratio. When the drawing ratio was 10, the CPET monofilament had a tensile strength of 717.2 MPa, an initial modulus of 16.7 GPa, and a maximum torsional modulus of 1.3 GPa. Therefore, both heat treatment and cross‐linking increased the mechanical strength of the PET monofilaments. CPET and HTPET are possible to be used as artificial muscles.